Minuteman UPS PN-34000247 User Manual download pdf

PN-34000247 Rev0

ParaShield 1224

User’s Manual

ParaShield 1224 is designed to provide a local power solution for cable

telephony, wireless local loop (WLL), and fiber to the home (FTTH)

broadband equipment.

IMPORTANT SAFETY WARNINGS

(SAVE THESE INSTRUCTIONS)

This manual contains important instructions regarding the installation and

operation of this device. Read this manual thoroughly before attempting to

unpack, install or operate this device

CAUTION! The battery can energize hazardous live parts inside even

when the AC input power is disconnected.

CAUTION! To reduce the risk of electric shock, do not remove the cover,

except to service the battery. No user serviceable parts inside, except for the

battery.

CAUTION! To avoid electric shock, turn off the unit and unplug it from the

AC power source before servicing the battery or installing your equipment.

INSTALLATION

(QUALIFIED SERVICE PERSONNEL ONLY)

Please read this manual before installing this DC UPS as it provides important

information that should be followed during the installation and repair of the DC

UPS:

1.) The ParaShield 1224 is intended to be installed in a temperature controlled

environment that is free of conductive contaminants. Select a location which

will provide good air circulation for the DC UPS at all times. Avoid locations

near heating devices, water or excessive humidity, or where the DC UPS is

exposed to direct sunlight. Route power cords so they cannot be walked on

or damaged.

2.) Remove the cover.

3.) Remove the battery.

4.) The wall mount screws must be the appropriate size for total weight of the

UPS and the mounting structural material.

5.) Connect the battery negative (Black) wire to the battery negative terminal.

6.) Connect the battery positive (Red) wire to the battery positive terminal.

7.) Re-install the battery into the case.

8.) Connect the output wires and connector to the DC UPS.

9.) Connect the Communications Signal wires to the DC UPS.

10.) Re-install the cover.

11.) See the section “Operation” for the startup procedure.

OPERATION

1.) Plug the DC UPS power cord into the AC inlet on the DC UPS.

2.) Plug the DC UPS power cord into the wall outlet.

3.) Turn on the connected equipment.

4.) The DC UPS is ready for normal operation.

The DC UPS charges the battery when it is connected to utility

power. It is recommended that the battery charge for minimum of

18 hours before use. The DC UPS may be used immediately,

however, the “On Battery“ runtime may be less than normally

expected.

BATTERY REPLACEMENT

(QUALIFIED SERVICE PERSONNEL ONLY)

This DC UPS has a hot-swappable battery. Hot-swappable battery means

that the battery can be replaced without powering down the whole DC UPS

system.

If there is a power interruption while replacing the hot-swappable

battery, with the DC UPS on, the load will not be backed up.

CAUTION!

Do not open or mutilate batteries. Released electrolyte is harmful

to the skin and eyes and may be toxic.

Do not dispose of batteries in a fire. The batteries may

explode. The batteries in this UPS are recyclable.

Dispose of the batteries properly. The batteries contain

lead and pose a hazard to the environment and human

health if not disposed of properly. Refer to local codes

for proper disposal requirements or return the battery to

MINUTEMAN in the packing material for the new

battery.

CAUTION!

Although battery system voltages are only 12VDC the battery

system can still present a risk of electrical shock. The current capability of a

battery is sufficient to burn wire or tools very rapidly, producing molten metal.

Observe these precautions when replacing batteries:

1.) Remove watches, rings, or other metal objects.

2.) Use hand tools with insulated handles.

3.) Wear protective eye gear (goggles), rubber gloves and boots.

4.) Do not lay tools or other metal parts on the top of the batteries.

5.) Disconnect the charging source before connecting or disconnecting the

battery terminals.

6.) Determine if the battery is inadvertently grounded. If the battery is,

remove the source of the grounding. Contact with any part of a grounded

battery can result in an electrical shock. The likelihood of such shock will be

reduced, if such grounds are removed during installation and maintenance.

Step 4. Connect the black cable to the battery negative terminal on the new

battery.

Step 5. Connect the red cable to the battery positive terminal on the new

battery.

Step 6. Install the new battery into the battery compartment.

Step 7. Tighten the battery stripe to secure the battery.

Step 8. Re-install the battery cover.

Step 9. The DC UPS is ready for normal operation.

Step 10. Dispose of the old battery properly.

Warning Indicator

● Front Panel

Indicator Color Condition

Green DC UPS is on utility power.

Yellow DC UPS is on battery power.

Green DC output power is provided by the battery or

utility power.

Red The battery is not connected or the battery needs

to be replaced.

1 2

Summary of Contents

Page 1 - User’s Manual

PN-34000247 Rev0 ParaShield 1224 User’s Manual ParaShield 1224 is designed to provide a local power solution for cable telephony, wireless local loo

Page 2 - Cold Start

PN-34000247 Rev0 ● Back Panel ○ Buzzer On/Off Switch: The default position of the buzzer switch is OFF. If you want to enable this function, t

Comments to this Manuals

No comments

Minuteman UPS PN-34000247 User Manual

Browse online or download User Manual for Uninterruptible power supplies (UPSs) Minuteman UPS PN-34000247. Minuteman UPS PN-34000247 User's Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Uninterruptible power supplies (UPSs) Minuteman UPS PN-34000247